Disclosure: Some product links are affiliate or referral links. As an Amazon Associate, Weld Support Parts earns from qualifying purchases. Other marketplace links may also earn a commission at no extra cost to you. Learn more.

Miller MIG accessory lookup

Miller MIG Drive Roll Lookup

Start with the catalog section, then match wire diameter and wire type. Drive rolls are selected by feed setup, not by machine name alone.

Pick the catalog section

Which Miller Drive-Roll Table Do You Need?

The Miller parts catalog separates small-machine drive-roll kits from larger 2-roll and 4-roll feeder systems. Pick the matching section first, then use the grouped table on that page.

Miller catalog section

Millermatic / Multimatic Drive Roll Kits

Use this page when the Miller catalog lists a drive-roll kit with two drive rolls and one inlet guide. This fits the smaller Millermatic and Multimatic-style drive-roll lookup path.

26 catalog rows V-Grooved: 8 | U-Grooved: 8 | V-Knurled: 10
Open this catalog section

Miller feeder systems

Miller 2-Roll / 4-Roll Drive Roll Systems

Use this page for larger Miller feeder setups where the catalog separates 2-roll kits, 4-roll kits, individual rolls, inlet guides, intermediate guides, and antiwear guides.

29 catalog rows V-Grooved: 8 | U-Grooved: 9 | Polished U-Grooved: 3 | V-Knurled: 9
Open this catalog section

Start here

Start With Your Machine

These machine paths help confirm which catalog section to open. Use them as routing shortcuts before ordering drive rolls or guides.

Machine path

Millermatic 211 Drive Roll Path

Older discontinued Millermatic 211 machines list Quick Select drive roll 261157 for .024 in. solid, .030/.035 in. solid, and .030/.035 in. flux-cored wire. The older data sheet also lists V-Knurled dual-groove drive roll 202926 for flux-cored wire.

  • Confirm the machine is the older 211, not 211 PRO.
  • Match wire diameter.
  • Use Quick Select 261157 for the listed solid and flux-cored sizes.
  • Use V-knurled 202926 where the data sheet calls for the flux-cored roll.
Open machine page

Machine path

Millermatic 211 PRO Drive Roll Path

Current Millermatic 211 PRO packages list a Quick Select drive roll for .024 in. solid, .030/.035 in. solid, and .030/.035 in. flux-cored wire. If the installed drive roll is not the Quick Select style, match the wire diameter and wire type against the Miller table below.

  • Confirm the front panel says 211 PRO.
  • Match wire diameter.
  • Use V-groove for solid hard wire.
  • Use V-knurled for flux-cored wire.
Open machine page

Machine path

Multimatic 220 AC/DC Drive Roll Path

For the Multimatic 220 AC/DC, choose the active process first. Use the MIG drive-roll table for wire-feed setup, the Spoolmate path for aluminum spool-gun setup, and the TIG torch path for TIG consumables.

  • Confirm MIG gun or spool gun.
  • Match wire diameter.
  • Use U-groove for aluminum feeder setup.
  • Use the spool-gun breakdown when the Spoolmate is installed.
Open machine page

Machine path

Millermatic / Multimatic Two-Roll Family

Use this family table for Miller Millermatic and Multimatic feeder paths covered by the Miller accessory drive-roll listing. Confirm the exact machine, feeder style, and inlet guide before ordering.

  • Match the feeder style.
  • Use the kit number when replacing both drive rolls.
  • Use the individual part number when replacing a single roll.
  • Verify inlet guide number when wire feeding is inconsistent.
Open machine page

Machine path

Miller Two-Roll / Four-Roll Systems

Use this table when the machine or feeder uses a 2-roll or 4-roll drive system. The 4-roll kit, intermediate guide, and antiwear guide matter on larger feeder setups.

  • Confirm 2-roll or 4-roll system.
  • Match wire type and wire diameter.
  • Check inlet and intermediate guide numbers.
  • Do not mix soft-wire U-groove and flux-cored V-knurled rolls.
Open machine page

Choose By Wire Type

V-Grooved
Hard wire such as common solid steel MIG wire.
U-Grooved
Soft wire and aluminum feeder setups.
Polished U-Grooved
Soft-wire feeder paths where Miller calls out polished rolls.
V-Knurled
Hard-shelled flux-cored wire.

Before Ordering

  • Confirm the machine or feeder drive system.
  • Match the exact wire diameter.
  • Confirm kit number versus individual roll number.
  • Check inlet guide fit when wire feed is inconsistent.

Related Pages

Miller drive-roll overview Millermatic / Multimatic kits 2-roll / 4-roll systems All drive rolls Miller MIG machines Wire feed problems